H-1030 “BIG BITE” TUB GRINDER

The latest introduction to the Haybuster PTO tub grinder family is the H-1030 model. It also has a 10’ tub and comes equipped with tub tilt and heavy-duty hammermill, that is located in the rear of the tub. It also has a dual-auger system to discharge material efficiently to the hydraulic folding stacking conveyor. The H-1030 requires a minimum of 150 hp up to 315 hp tractor. The newly designed electronic governor protects the tractor and machine from overloads, allowing the tub grinder to grind efficiently and consistently.


H-1030 Big Bite General Specifications

WEIGHT
Total 13,300 lbs (6,032.78 kg)
Hitch 1,925 lbs (873.17 kg) with conveyor raised and folded

TRANSPORT DIMENSIONS
Width 10′ 4″ (3.15 m)
Height 10′ 1″ (3.07 m)
Length 19′ 4″ (5.89 m)

OPERATING DIMENSIONS
Total Width 10′ 2″ (3.10 m)
Total Width, Tub Raised 11′ 9″ (3.58 m)

CHASSIS FEATURES
Towing Arrangement Clevis hitch
Tires (2) 16.5L x 16.1 SI – 14 Ply High Flotation Implement Tires
Wheels (2) 16.1 x w14c – 8 Bolt, 6″ (15.24 cm) Pilot
Bearings Tapered roller bearings

TUB FEATURES
Loading Height 9′ 2″ (2.79 m)
Tub Width at Flare 10′ 2″ (3.10 m)
Depth 44.1″ (1.12 m)
Tub Inside dia at Base 95.5″ (2.43 m)
Tub Wall Thickness 12 gauge (2.66 cm)
Tub Floor Thickness 10 gage (3.42 mm)

HAMMERMILL – HEAVY DUTY
Length 43″ (109.2 cm)
Diameter, Hammers Extended 26″ (66.04 cm)
Feed Opening 28” x 45” (71.1 cm X 114.3 cm)
Hammers HD-1/2″ (12.7 mm) A.B. Hardened Steel, Swing
Number of Hammers 64
Hammer Rods 1-1/4″ (31.75 mm) Dia, Case-Hardened
Cylinder Plates HD Mills: 3/8″ (0.95 cm) Thick x 15 3/4″ (40.01 cm)
Cylinder Shaft 3 1/2″ (8.89 cm) Stress Proof Steel
Bearings 3″ (7.62 cm) Pillow Block
Drive PTO through Multiple V-Belts, 1,000 RPM, 1-3/8″ dia. 21 spline shaft, or 1-3/4″ dia. 20 spline shaft
Screens 1/8″ (3.18 mm), 3/16″ (4.76 mm), or ¼” (6.35 mm) Thick and Various Hole Sizes from 1/8″ (3.18 mm) to 8″ (203.2 mm) – Must Order 2 Screens of Choice With Machine-Not Standard equipment

BELLY AUGERS
Size Twin 12″ (30.48 cm) diameter x 48″ (121.92 cm) long
Drive Hydraulic

DISCHARGE CONVEYOR
Type Rubber Belt with cleats
Drive Hydraulic
Drive & Idler Roller Type Rubber Lagged Drive Pulley, “Easy Clean” Idler
Length 21′ (6.4 m)
Width 24″ (60.96 cm)
Maximum Conveyor Lift Height 14′ 9″ (4.5 m) @ 40° Incline
Conveyor Lift Hydraulic
Conveyor Lift Cylinder 3-1/2″ x 20″ (8.89 cm x 50.8 cm)
Conveyor Fold Hydraulic

OPERATOR CONTROLS
Tub Rotation Wachendorf A35 display switch controlled Clockwise, Stop, & Counter-Clockwise
Tub Speed Wachendorf A35 with ECU 710 Control Electronic Governor Stabilizes Engine Load by Adjusting Tub Rotation Speed
Conveyor Lift & Fold Electric/Hydraulic Switch Control Uses Tractor SCV
Tub Tilt Electric/Hydraulic Switch Control Uses Tractor SCV
Conveyor On/Off Wachendorf A35 display switch controlled

REQUIREMENTS FOR OPERATION TRACTOR
PTO Horsepower Required 150 HP (118.85 kw) to 315 HP (234.9 kw)
Min. Hydraulic Output 8 gpm at 1,500 psi (30.3 lpm. x 10,345 kPa)
Hydraulic Remote Controls 1 Double-Acting Control Valves With Quick Coupler Outlets
Electrical 12 VDC

GRINDER
Hydraulic Reservoir Capacity 60 gallons (227.13 L) of Hydraulic Oil
(Mobile 423, CENEX Super HTB or Equivalent)
Mill Grate Kit This kit includes; 5 removable mill grates, and 6 removable slug bars for improved grinding performance in tough hay and stover.

H-1030 Big Bite Options

PTO Shaft -1000 RPM
Tractor Half, 1-3/4 in, 20 Spline Shaft
Tractor Half, 1-3/8 in, 21 Spline Shaft

Geyser Plates
Geyser Plate Kit, use with the Slug Buster
Geyser Plate Kit, slotted, use with the Mill Grate

Hopper for Grain Grinding

Ear Corn Kit
Better diets for dairy cows – an article from the USDA – describes how finely ground grains/corn can offer a better diet for cows.

Closed Center Conversion Kit
This kit is required to operate the conveyor lift valve properly, with John Deere 60 and older series tractors.

Grinding Screens
1/8 in. (3.18 mm) Round Hole Screen Half*
3/16 in. (4.76 mm) Round Hole Screen Half**
1/4 in. (6.35 mm) Round Hole Screen Half
3/8 in. (9.52 mm) Round Hole Screen Half
1/2 in. (12.7 mm) Round Hole Screen Half
5/8 in. (15.88 mm) Round Hole Screen Half
3/4 in. (19.05 mm) Round Hole Screen Half
1 in. (25.4 mm) Round Hole Screen Half
1-1/2 in. (38.1 mm) Round Hole Screen Half
2 in. (50.8 mm) Round Hole Screen Half
3 in. (7.62 cm) Round Hole, Screen Half (standard)
4 in. (10.16 cm) Round Hole, Screen Half (standard)
5 in. (12.70 cm) Round Hole, Screen Half (standard)
6 in. (15.24 cm) Round Hole, Screen Half (standard)
7 in. (17.78 cm) Round Hole, Screen Half (standard)
8 in. (20.32 cm) Round Hole, Screen Half (standard)
Dummy (Open) Screen Half
*1/8 in. (3.18 mm) thick,
**3/16 in. (4.76 mm) thick, all other screens are 1/4 in. (6.35 mm) thick

Call Now 1(800) 352-6257