Model 9564 Horizontal Grinder is ideal for the largest jobs. It is designed for efficiency with a large conveyor and has the ability to grind as fast as it is loaded. The 9564 uses its high-capacity 315 cu. ft. (11.66 cu. yd.) (8.91cu.m.) hopper that is 20’ 8” long to grind up long trees, brush and other green waste. The largest grinder in the DuraTech line, it’s powered by a CAT C27 Tier II diesel engine rated at 1050 horsepower (782.9 kw), connected to an HPTO wet clutch that transfers power to the 64 inch wide 12,100 lb. (5488.5 kg) hammermill.


General Specifications (Model 9564)

WEIGHT / AXLE / SUSPENSION
Spacing 57-1/2 in. (1.46 m)
5th Wheel Weight 33,750 lbs. (15,308.74 kg)
Total Axle Weight 57,750 lbs. (26,195 kg)
Total Weight 91,500 lbs. (41,503.7 kg)

MACHINE DIMENSIONS
Transport Width 11 ft. 10 in. (2.59 m)
Transport Height 13 ft. 5 in. (4.09 m)
Transport Length 53 ft. (15.18 m)

DRIVE SYSTEM
Engine Caterpillar C-27 Tier II 1050 HP (782.9 kW) Diesel Engine
Clutch HPTO 15 TD Wet Clutch
Fuel Capacity 380 Gallons (1,440 L)
Fuel Consumption 45.7 gal./hr. (179.8 L/hr)
Hydraulic Oil Capacity 145 Gallons (548.9 L)
Rotor Drive 10 Groove 8V

FEED SYSTEM
Hopper Capacity 315 Cubic Ft. (8.91 cu. m)
Hopper Width 61-1/2 in. (156.2 cm) Bottom, 74 in. (187.7 cm) Top
Hopper Length: 248 in. (629.9 cm) Door Up
300 in. (762 cm) Door Down
Hopper Depth 35 in. (88.9 cm)
Feed Opening 61-1/2 in. X 40 in. (156.2 cm x 106.6 cm)
Feed Height 96 in. (234.8 cm)

GOVERNING SYSTEM
Electric (PLC) Programmable Logic Controller
Hydraulic Drives Two Load Sensing Pumps
The PLC (Programmable Logic Controller) regulates feed rate based on rotor speed. Feed rate is proportional to rotor speed. Maximum feed rate is adjustable. Hammermill weight consists of shaft, hammer rods, bits, hardware, and tool holders.

HAMMERMILL
Rotor Shaft Size 5-7/16 in. (13.81 cm)
Rotor Width 64 in. (162.6 cm)
Rotor Speed 1,125 RPM
Tip Swing Diameter 50-3/4 in. (126.9 cm)
Number of Tips 24
Cylinder Mid Plates 1-1/2 in. (3.81 cm) Thick x 39 in. (99.06 cm) Diameter
Cylinder End Plates 1-1/2 in. (3.81 cm) Thick. x 40 in. (101.06 cm) Diameter T-1 Material
Weight 12,100 lbs. (5488.47 kg)
Hammer Rod Size 3-1/4 in. (8.26 cm)

FEED ROTOR
Rotor Diameter 42 in. (106.9 cm)
Drive Dual Orbit Motor / Double Reduction Gearboxes

SCREENS
Screen Area 4,340 sq. in. (27,99.944 sq. cm)
Thickness 1 in. (2.54 cm)
Hole Sizes Available in a variety of sizes

BELLY CONVEYOR
Length 28-1/2 ft. (8.69 m)
Width 54 in. (137.2 cm)

STACKING CONVEYOR
Length 30.5 ft. (9.3 m)
Width 48 in. (121.9 cm)
Oscillating 40 Degree side-to-side
Stacking Height 22′ (6.71 m) @ 30 Degree Incline

OPTIONS
Air Compressor Available
Magnetic Roller Available

Call Now (352) 812-9197