DuraTech Model 3010 Industrial Tub Grinder is a mid-sized tub grinder that can handle logs up to 32” in diameter. This machine is a step above the 2009, and the perfect option when the 2009 cannot handle the task. The 3010 is among the most efficient and productive grinders on the market, and feature a 30″ (76.2 cm) wide oscillating stacking conveyor and self-cleaning radiator screen. It is powered by either a CAT C15 475 horsepower (354.21 kw) or 540 horsepower (402.68 kw) Tier III Diesel Engine, with a PT Tech Fluid Clutch system that drives a heavy-duty hammermill.


SPECIFICATIONS [model 3010F]

WEIGHT
Weight w/Fifth Wheel Hitch 38,000 lbs. (17,236.51 kg)

TRANSPORT DIMENSIONS
Transport Width 8 ft. 6 in. (2.54 m)
Transport Height 11 ft. (3.35 m)
Transport Height w/ Tub Cover 135.82 in. (345.01 cm)
Transport Length w/ Fifth Wheel 42 ft. 11-3/4 in. (13.10 m)

CHASSIS FEATURES
Axle (2) – 22,500 lbs. (10,205.82 kg)
Electrical 24 volt machine
Tires 255/70R X 22.5
Engine: 475 hp (354.21 kW) CAT C15 Tier III
540 hp (402.68 kW) CAT C15 Tier III
Fuel Capacity 300 Gallons (1,135.6 Liters)
Hydraulic Oil Capacity 50 Gallons (189.3 Liters)
Lights Clearance, Directional

TUB
Tub Width 10 ft. (3.04 m)
Depth 46 in. (116.84 cm)
Tub Diameter at Base 8 ft. (2.43 m)
Tub Wall 1/4 in. (.635 cm) Thick
Tub Floor 3/8 in. (.953 cm) Thick
Tub Drive 120H Chain, Single Drive Hydraulic Motor
Service Access 90° Tilting Tub
Tub Speed Sensor Electronic Self Governing

CONVEYORS
Stacking Conveyor 26 ft. (7.92 m) Long x 30 in. (76.2 cm) Wide
Belly Conveyor 30 in. (76.2 cm) Wide Impact Resistant

HAMMERMILL
Hammers 20 Fixed Single Bolt or 40 Swinging
Rotor – Shaft Diameter 6 in. (15.24 cm) Stress Proof Steel
Rotor Length 44 in. (111.76 cm)
Rotor Plates 16 in. (40.64 cm) Diameter x 1-1/2 in. (3.81 cm) Thick
Feed Opening 45 in. x 25 in. (114.3 cm x 63.5 cm)
Screen Area 2,403 Square Inches (15,503.19 sq. cm.)
Hammer Rods (8) – 1-1/2 in. (3.81cm) Diameter
Bearings 4 in. (10.16 cm) Oil Bath Bearing
Hammermill Drive Direct Drive through HPTO Oil Cooled Clutch

*3010 Fifth Wheel Tub Grinder Options

Hammer Options: (Must choose one)
(38) 3/4″ x 3″ Swing Hammers
(38) 1″ x 3″ “Supreme” Swing Hammers
(20) Fixed Hammers

Screen Options: (Must choose one)
Screen 1″ Hole 1/2″ Thick Hardox w/ Doubler
Screen 1 1/2″ Hole 1/2″ Thick Hardox w/ Doubler
Screen 2″ Hole 1″ Thick
Screen 3″ Hole 1″ Thick
Screen 4″ Hole 1″ Thick
Screen 4 3/4″ x 7″ Hole 1″ Thick
Screen 6″ x 9″ Hole 1″ Thick

Discharge Conveyor Drive Roller: (Must choose one)
Top Drive Roller
Magnetic Roller Complete w/ Aluminum Deflector Chute

Remote Control Option: (Must choose one)
No Remote Control
6 Function Tub: Start, Stop, Rev Cnvyr: Up, Down Eng: Kill
6 Function plus Cover: Raise, Lower

Mill Cover

12 hp Compressor w/ Vandal protection, 50′ of 1/2″ hose with reel (5th Wheel Only)

3/4″ Air Impact w/ Two Sockets & Extension

Lockable Steel Toolbox

Hydraulic Front Stabilizer Jacks

12′ Tub Flare Extension (unavailable w/tub cover)

Tub Agitator Kit

Hammer Rod Puller

Tub Cover
An operational characteristic of all grinders is that objects may be thrown out of the tub. Tub Covers reduce the risk of potential injury or property damage from thrown objects. Proper use of the Tub Cover provides the operator with a means to help control the area over which thrown objects may fall. Combined with a decrease in the percentage of objects thrown from the tub, the Tub Cover is an effective means of reducing risk to personnel and property.

Call Now (352) 812-9197