Meet the newest addition to the DuraTech family of grinders, the Model 5064 Horizontal. This Heavy Duty midsized grinder is available in a trailer model or mounted on tracks. It is available with your choice of CAT Tier III engines to meet your grinding needs. Choose from 475 HP (354 kw), 540 HP (403 kw), or 630 HP (470 kw), all with a HPTO 14 TD wet clutch for your specific requirements of productivity and efficiency.
The large 61.5” (156.2cm) X 35” (88.9cm) feed opening allows material to flow to the 64” (162.5cm) wide 8,850 lb( 3,878 kg) hammermill for superb grinding performance. The programmable logic speed control (PLC) governs the product flow through the 13’2” (4.01m) 197 Cubic Foot (5.59 Cubic Meter) feed hopper for maximum grinding efficiency. The optional remote control allows the operator to have complete control of the grinder while operating support equipment.
If you want a horizontal grinder that will give you maximum return on your investment, check out the DuraTech 5064 Horizontal Grinder.
General Specifications (model 5064T)
Total Weight 80,000 lbs. (36,287.4 kg)
CAT 320 L Track System 20″ (50.8 cm) Wide x 15′ (4.6 m) Long Steel Track
Transport Width 9 ft. 10 in. (3 m)
Transport Height 11 ft. 5 in. (3.48 m)
Transport Length 37 ft. 8 in. (11.48 m)
Engine: Caterpillar C-18 Tier III 630 HP (470 kw) Diesel Engine
Caterpillar C-15 Tier III 540 HP (403 kw) Diesel Engine
Caterpillar C-15 Tier III 475 HP (354 kw) Diesel Engine
Clutch HPTO 14 TD Wet Clutch
Fuel Capacity 300 Gallons (1,135 L)
Hydraulic Oil Capacity 145 Gallons (548.9 L)
Rotor Drive 4 Groove Belt
Hopper Capacity 197 Cubic Ft. (5.59 cu. m)
Hopper Width 61-1/2 in. (156.2 cm) Bottom, 74 in. (187.7 cm) Top
Hopper Length: 13 ft. 2 in. (4.01 m)
Hopper Depth 35 in. (88.9 cm)
Feed Opening 61-1/2 in. X 35 in. (156.2 cm x 88.9 cm)
Hopper Loading Height 96 in. (234.8 cm)
Feed Roller 36 in. (91.44 cm) dia.
Load Speed Sensor Programmable Logic Controller
The PLC (Programmable Logic Controller) regulates feed rate based on rotor speed. Feed rate is proportional to rotor speed. Maximum feed rate is adjustable. Hammermill weight consists of shaft, hammer rods, bits, hardware, and tool holders.
Weight 8,550 lbs. (3,878 kg)
Rotor Bearing Diameter 4-7/16 in. (11.27 cm)
Rotor Shaft 7 in (17.78 cm) Alloy Steel
Rotor Width 64 in. (162.6 cm)
Rotor Plates 32-1/4 in. (81.92 cm) dia. X 1-1/2 in. (3.81 cm) Thick
Tip Swing Diameter 41 in. (104.14 cm)
Number of Hammers 32 Single Bolt
Hammer Rods (16) – 2 in. (5.08 cm) dia.
Screen Area 3,705 sq. in. (2.39 sq. m)
Hole Sizes Available in a variety of sizes
Length 22 ft. (6.71 m)
Width 54 in. (137.2 cm)
Length 13 ft. (4.06 m)
Width 48 in. (121.92 cm)
Lights Clearance, Directional
Air Compressor Available
Magnetic Roller Available